如何使用Qt自定義控件實現簡易儀表盤

這篇文章將為大家詳細講解有關如何使用Qt自定義控件實現簡易儀表盤，小編覺得挺實用的，因此分享給大家做個參考，希望大家閱讀完這篇文章后可以有所收獲。

Qt自定義控件12：簡易儀表盤

思路：畫270度的圓弧，圓弧根據占比分為兩種顏色，根據占比在圓弧上畫出一個圓球作為標志，然后就是刻度線和刻度值。刻度線是根據坐標系旋轉畫出，刻度值是根據角度求出x,y坐標值構造出一個矩形畫出刻度值（不要用坐標系旋轉畫刻度值，那樣刻度值的角度也會旋轉，寫出的字不是正的，效果不好）。最后就是在中心畫value。

關鍵代碼：

void CMPassrate5::paintEvent(QPaintEvent *event){  int width = this->width();  int height = this->height();  int side = qMin(width, height);  QPainter painter(this);  painter.setRenderHints(QPainter::Antialiasing | QPainter::TextAntialiasing);  painter.translate(width / 2, height / 2);  painter.scale(side / 200.0, side / 200.0);  drawE(&painter);  drawEPoint(&painter);  drawLine(&painter);  drawEText(&painter);  drawValue(&painter);}void CMPassrate5::drawE(QPainter* painter){  QRect rect(-radius,-radius,2*radius,2*radius);  painter->save();  painter->setPen(Qt::NoPen);  QPainterPath path;  QPainterPath subPath;  QPainterPath outPath;  QPainterPath outPubPath;  outPath.arcTo(rect,-45,outRange);  outPubPath.addEllipse(rect.adjusted(side,side,-side,-side));  outPath -= outPubPath;  color.setAlpha(100);  painter->setBrush(color);  painter->drawPath(outPath);  path.arcTo(rect,-45+outRange,range);  subPath.addEllipse(rect.adjusted(4,4,-4,-4));  path -= subPath;  color.setAlpha(180);  painter->setBrush(color);  painter->drawPath(path);  painter->restore();}void CMPassrate5::drawEPoint(QPainter* painter){  //圓球位置就在outRange盡頭處  painter->save();  color.setAlpha(180);  painter->setPen(Qt::NoPen);  painter->setBrush(color);  float x = (radius-side/2)*qCos((range+135)*3.14/180);  float y = (radius-side/2)*qSin((range+135)*3.14/180);  qDebug()<<"x:"<<x<<" y:"<<y;  painter->drawEllipse(QPoint(x,y),side,side);  painter->restore();}void CMPassrate5::drawLine(QPainter* painter){  painter->save();  painter->rotate(135);  color.setAlpha(100);  painter->setPen(color);  QLine line(QPoint(radius-side-lineLength,0),QPoint(radius-side,0));  for(int i = 0;i<lineCount;i++){    painter->drawLine(line);    painter->rotate(270.0/lineCount);  }  painter->restore();}void CMPassrate5::drawEText(QPainter* painter){  painter->save();//  painter->rotate(135);  painter->setPen(Qt::black);  float textRange = 270.0/(textCount-1);  float x,y;  for(int i = 0;i<=10;i++){    x = (radius-side-lineLength)*qCos((textRange*i+135)*3.14/180);    y = (radius-side-lineLength)*qSin((textRange*i+135)*3.14/180);    if(i<5){      QRect rect(x,y-4,20,10);      painter->drawText(rect,Qt::AlignCenter,QString::number(i*10));    }else if(i ==5){      QRect rect(x-7,y,20,10);      painter->drawText(rect,Qt::AlignCenter,QString::number(i*10));    }else{      QRect rect(x-20,y-5,20,10);      painter->drawText(rect,Qt::AlignCenter,QString::number(i*10));    }  }  painter->restore();}void CMPassrate5::drawValue(QPainter* painter){  painter->save();  QPen pen = painter->pen();  pen.setColor(color);  pen.setWidth(2);  painter->setPen(pen);  QFont font = painter->font();  font.setPixelSize(45);  painter->setFont(font);  QRect rect(-25,-25,50,50);  painter->drawText(rect,Qt::AlignCenter,QString::number(value));  painter->restore();}

關于“如何使用Qt自定義控件實現簡易儀表盤”這篇文章就分享到這里了，希望以上內容可以對大家有一定的幫助，使各位可以學到更多知識，如果覺得文章不錯，請把它分享出去讓更多的人看到。